Joined in 2023 
82 
63 About this deal
Reusable desiccants are a much more affordable solution to removing moisture from wherever you store filament than disposable varieties. Reusable desiccant can be placed in the oven, microwave, or food dehydrator to dry out and recharge each time it fills with too much moisture and can’t absorb any more. This will cut down on your waste if you require lots of desiccant to dry filament. Color Indication Push down lever toward the upper body of the plug and lever plug upwards. Resistance will be encountered but the plug will pop out. Never insert the lever into the funnel or slot. This can cause a lot of issues during the printing process. Your filament can snap mid-print, and if your 3D printer doesn’t have a filament sensing feature, your print will fail. It’s also easy for the filament to get jammed in the extruder during a filament change, so that is a possibility as well when you have to feed the end of the filament into the printer again. Print Quality This dryer features electronic heating, drying, and a humidity sensor with a real-time display. This allows you to dry out and salvage filament spools that have already absorbed moisture and need it removed or to ensure that a new roll of filament is completely dry before using it for the first time.
PolyBox™ features 6 filament guide holes and a reversible casing, this means no matter where your extruder feeds from there is an orientation that will suit your 3D printer. PolyBox™ comes with 150cm of filament guide tube to shield your filament from the PolyBox™ to the extruder. Each filament guide hole comes with a rubber plug to seal the PolyBox™ when not in use. Image: Ken73 via Thingiverse This solution can be used with any appropriately sized vacuum bag Plastic Storage Boxes PolyBox has a thermo-hygrometer to monitor the filaments in the box. The humidity is regulated by large desiccant bags.
You may also like…
While wet filament usually doesn’t appear any different than dry filament while on the spool, there are a few major indicators that your 3D printing filament has absorbed moisture. Brittleness
printer filament is made from thermoplastic polymers, which are materials that can be melted and molded into different shapes. The quality and performance of the filament may change over time if it is exposed to excessive heat, humidity, or moisture. For this reason, it is important to store the filament in a cool, dry place when not in use. What humidity should 3D filament be stored at? Using a manual storage solution similar to that of food and produce storage, the PrintDry Vacuum Sealed Filament Storage System is a set of five round plastic containers that are large enough to fit most standard spool sizes. Each container can fit one spool and has a hole in the lid that allows you to pump out any air from the container with the included hand pump. Our Poly Plus boxes have the same great insulating properties as our regular poly boxes with the added extra of an outer corrugated cardboard sleeve. The cardboard outer not only adds another thermal layer of insulation from exterior elements but also helps to further protect your goods while in transit. Poly Plus Boxes ensure your quality produce arrives intact, fresh and well presented to your end customers and what’s more, the corrugated outer box means you can now display your branding if you should so choose.Using a storage solution with an airtight seal such as vacuum bags or storage boxes is key to keeping water from contaminating your filaments, but that won’t be enough if your filaments are already contaminated. You can dry your wet filaments with a dry cabinet, filament dryer, and even a food dehydrator.
PolyBox’s main focus is to use receipts data and provide reports based on users’ needs. This also gives clients a better understanding of expenses, budget allocation, and how to improve the way money is spent. The PolyBox can hold two 1kg spools or one 3kg spool and is compatible with 1.75mm and 2.85mm filament. The spools are placed on bearings and the filament is fed through one of the 6 exit holes. This means that the PolyBox is compatible with almost any printer setup.
The box features two PTFE outlets in the lid that allow you to print with your filament while it is in the box. You can also close the outlets during the drying process or when storing your filament spool for an extended time. Our Standard Poly Box range represents the traditional polystyrene shipper that has been tried and tested for many years, delivering everything from Christmas turkeys, to farmhouse cheeses, to wet fish. Having built-in heating and drying features ensure that your filament dries evenly and thoroughly. These solutions are great for not only preventing moisture in your filament spools but also making them usable again in the event that they do take on too much water. Ease of Use How PLA filament is stored is an important consideration for filament quality. It’s best practice to store filament in a filament storage container when not in use. This will help keep the filament from absorbing moisture from the air and will help maintain its quality and printability. PolyBox™ can print with two 1kg spools simultaneously perfectly suited to dual extrusion printing or use one 3kg spool for longer prints or industrial users. Cut the 150cm filament guide tube to suit your setup.
Some desiccants use color indication to let you know when it can no longer absorb water. This means that the beads will change color whenever they need to be dried out or replaced. This is a nice feature because it takes the guesswork out of knowing when to change the desiccant in your storage containers. That way, you won’t leave them in longer than you should and risk your filaments taking on too much moisture. Amount Some enclosed 3D printers store their filament internally, preventing it from absorbing too much moisture from the ambient air. How do you store open 3D filaments? Este sistema isotérmico con control de temperatura ha sido diseñado para trabajar principalmente con productos que necesitan ser almacenados y transportados durante 72 -120 horas en tres rangos de temperatura: de 2°C a 8°C (refrigerado) y de 15°C a 25°C (ambiente).Humidity monitoring measures how much humidity is in the air, which is a useful feature to have in your filament storage solution. Knowing how high the humidity is inside your dry cabinets, storage boxes, etc. can help you ensure your filaments won’t absorb moisture from the air while in storage. Price How easy and accessible your filament storage solution is to use can make a huge difference in your user experience. A storage solution that allows you to print directly from the container is more convenient than, say, vacuum-sealed bags that only protect the filament while it’s not in use. How to Choose Desiccants for Filament Storage Rechargeability The Sovol SH01 Filament Dryer is a fantastic storage and drying solution for 3D printing filaments. With a capacity for two filament spools, you can easily swap between colors or feed to two printers at a time. Products like the Sovol SH01 Filament Dryer make this easy, because they allow you to store filament in its airtight chamber or dry it using its built-in heating element. These types of products are essential for keeping your filaments in good condition. PolyBox™ is a filament storage box that allows you to store materials in their optimum printing environment while still being able to print with them. PolyBox™ features a thermo-hygrometer to monitor your filaments inside the box. The humidity is regulated by large desiccant bags which absorb moisture from the air inside the PolyBox™. The PolyBox™ has been specifically designed for hygroscopic materials such as PolySmooth™, PVA or PolyMide™. The PolyBox™ can house two 1kg spools simultaneously or one 3kg spool and is compatible with both 1.75mm and 2.85mm filament diameters. Key Features:
Great Deal 
New Comment